Варианты индивидуальных заданий по деловому английскому языку производственной плавательной практики
Номер варианта индивидуального задания выбирается согласно таблице 1.1 (см. выше) по двум последним цифрам номера зачетной книжки.
Выполнить перевод и составить ответ (действия) на русском и английском языке.
0. Sea water cooling system. Draw schematic diagram showing pumps, valves, filters etc of this trace systems. Do it yourself and do not copy from ship's drawings. Label all main components.
1. Fresh water cooling system. Draw schematic diagram showing pumps, valves, filters etc of this trace systems. Do it yourself and do not copy from ship's drawings. Label all main components.
2. Lubricate oil system. Draw schematic diagram showing pumps, valves, filters etc of this trace systems. Do it yourself and do not copy from ship's drawings. Label all main components.
3. Fuel oil system. Draw schematic diagram showing pumps, valves, filters etc of this trace systems. Do it yourself and do not copy from ship's drawings. Label all main components.
4. Ballast system. Draw schematic diagram showing pumps, valves, filters etc of this trace systems. Do it yourself and do not copy from ship's drawings. Label all main components.
5. Discuss advantages and disadvantages of a central cooling system.
6. Sketch and describe the piston of the main diesel engine.
7. Sketch and describe the cylinder head of the main diesel engine.
8. Sketch and describe the crankshaft of the main diesel engine.
9. Sketch and describe the turbocharger of the main diesel engine.
10. Sketch and describe the bearings of the main diesel engine.
11. Sketch and describe the fuel pumps of the main diesel engine.
12. Sketch and describe the fuel injection valve of the main diesel engine.
13. Sketch and describe the fuel oil filters and lube oil filters of the main diesel engine.
14. What are the most highly stressed components of the main diesel engine?
15. What effect does a dirty air cooler have on a main engine and when would you consider a cooler to be dirty?
16. Sketch and describe the F. 0. purifier fitted on you vessel.
17. Describe the starting and stopping procedure of purifier. List normal operating pressures and temperatures.
18. How is the purifier bowl kept clean whist still in operation? Discuss the differences between full and partial discharge system. What is the purpose of the gravity disc, how is it selected and what purifiers do not require?
|
|
|
19. What is the main purpose of a purifier and a clarifier - and what is the difference in their construction?
20. Take F. 0. bunkers with the C/E and describe the procedure in full. Prepare the bunker plan and submit a copy with your answer.
21. Submit a copy of the bunker receipt and give a brief description of the following terms: Density, Viscosity, Flash point. Show how temperature effects quantity of bunkers taken.
22. Briefly explain the effects and counter measure for the following F. 0. contaminants: Sulphur, Vanadium, Silica, Catalytic fines.
23. Sketch and describe the main air compressor fitted on your vessel.
24. State starting and stopping procedures and list the items to be checked during operation. What affects the efficiency of the air compressor? Why is an air start compressor unsuitable for deck air?
25. For a main diesel generator on your ship, describe the procedure to Start.
26. For a main diesel generator on your ship, describe the procedure to Put on load in parallel.
27. For a main diesel generator on your ship, describe the procedure to Off load and shut down.
28. Sketch and describe the electrical power distribution system on board.
29. Describe how insulation resistance of electrical equipment is checked. List the factors, which influence and reduce insulation resistance. State the minimum safe insulation reading. What is expected to happen if insulation resistance is below the safe limit?
30. Identify the symptoms of poor combustion in a Diesel Alternator. State six reasons for poor combustion in such an engine. Describe the effects on engine condition and maintenance if poor combustion is allowed to persist.
31. List all certificates that your vessel must hold. For how long is each certificate valid and what is the expiry date? State who carries out each survey and list all items covered. What parts of a safety construction survey relate to engine room.
32. Sketch and describe the main oil fired boiler fitted on board.
33. Describe, for the main oil fired boilers, the procedure for flashing up and shutting down from a state of readiness normally kept in port.
|
|
|
34. Sketch and describe the exhaust gas boiler.
35. Sketch and describe the procedure for blowing down a main boiler gauge glass. Describe safety features on an oil fired boiler. Describe the following boiler water tests and treatment.
36. State acceptable parameters and the implication of operating outside the stated parameters: Chlorides, Alkalinity, Phosphate reserve, Hydrazine reserve.
37. Describe the following main engine jacket cooling water tests. State acceptable parameters and the implication of operating outside the stated parameters: Chlorides, Nitrite reserve.
38. Sketch and describe the general arrangement of the steering gear on board your vessel. Describe with the aid of diagrams, the operation of the hunting gear.
39. Describe the statutory tests required prior to leaving port. List the items checked daily while the vessel is at sea. How would you establish if a rudder was fouled?
40. Sketch and describe the following deck machinery: Windlass, Mooring winches.
41. Sketch and describe the following deck machinery: Hatch covers, Derricks (where fitted).
42. Sketch and describe the refrigeration plant fitted on your vessel.
43. Sketch and describe the F. W. Generator fitted on board. Include the normal operating pressures and temperatures.
44. How does the ambient air and sea temperature influence water production of the F. W. Generator? List the points to look for if production falls. How can production be increased?
45. Sketch and describe the O. W. S and 15 ppm oil monitor. Describe how to demonstrate the 15 ppm alarm function. Include an extract from the Oil Record Book and state how it is completed. When the 15 ppm alarm is activated, what else happens.
46. What elements of the ISM Code are related to engine room operations and how are these controlled.
47. Sketch and describe the fixed fire fighting installation for the engine room on your ship. Include instruction for operation.
48. Detail the symptoms of a main engine scavenge fire and list in order of priority the action that should be taken on discovery. What must be done if the engine stalls. How would you extinguish the fire if it will not bum out with the engine running. What causes scavenge fires and what can be done to avoid them.
49. Discuss advantages and disadvantages of Fixed foam, C02, Halon, Water spray / mist.
Дата добавления: 2018-05-12; просмотров: 323; Мы поможем в написании вашей работы! |
Мы поможем в написании ваших работ!