Q11.What can be added and edited in all manual update objects?
Geometry and attributes.
Slaves objects.
All the above.
Q12.How do you pan or shift the center position on the chart?
By moving the pointer to the left or right fast.
By holding the center button and moving the pointer or clicking the left button off-center with the pointer.
Move the pointer to the side, wait for it to turn into an arrow, and then left click.
Correct Answer!
Q13.In case of an alert, the alert indicator starts flashing and the audio sounds, what should you do to silence it?
Acknowledge the alert to silence it.
Do nothing about it as the ECDIS will automatically silence it.
Mute the audio so that the ECDIS is in silent mode.
Correct Answer!
Q14.An officer obtained a new PERMIT.TXT for a new route from Copenhagen to Dublin from AVCS for his USERPERMIT. He loaded the ENC from a DVD to the ECDIS database named “AVCS Base 3”. He switched on the “Display” for previous installed AVCS database and the newly installed “AVCS Base 3” database. What did he do wrong?
He should obtain a certificate, not a permit file to actually read the charts.
He should only switch on “Display” for the updated database.
He should not divide the base and update into two different databases in the ECDIS.
Correct Answer!
Q15.What do you do when own ship is moving towards an object classified as danger?
Avoid the object at all cost as ignoring it can lead to collision or grounding.
Exercise caution as the object is part of special navigational conditions.
Proceed with caution if you do not see or sense anything dangerous.
Correct Answer!
Q16.An icon (cogwheel with “Default” text) is shown in the top right icon bar. What is it for?
It sets the default colors on the chart according to time & position (e.g. daylight).
It sets parameters such as safety contour, safety depth, cross track limit to own ship defaults.
It selects the default user (instead of e.g. the master).
It sets the chart to a default mode (e.g. range 3nm) and turns off all “special modes” (e.g. full light lines).
Correct Answer!
Q17.An icon (circle with anchor) is shown in the top right icon bar. What is it for?
It is used to show or hide anchored or passive AIS ships.
It is a tool to make water-referenced versus ground-references EBL/VRM measurements with.
It is used to set an anchor watch.
It is used to set a waypoint for the anchor.
Correct Answer!
|
|
|
Q18.While navigating in “Show vessel“ mode the ship stays at the upper left corner of the view to your dismay. What can you do to fix it to the center?
Change to ship motion true mode.
Select navigation area as fixed position under “Chart” menu in “Settings” panel.
Change the ship redraw area.
Restart the ECDIS.
Click on “Keep best scale” in “Shortcuts” panel.
Correct Answer!
Q19.What are the coordinates in the status bar showing?
The position of the ship.
The next destination of the ship.
The position under the cursor.
Correct Answer!
Q20.Where do you view whether there are any outdated charts for a route?
Go to “Routes”, click on a route, and press “Chart report”.
Go to “Nav Data – Charts library” and click “Update history” for a chart library to check.
Go to “Nav Data – Charts library” and turn on “Graphical Index” to see updated and outdated charts.
Correct Answer!
Q21.You observed that data from some sensors are displayed in white, while data from other sensors are displayed in yellow color. What could be the reason?
Data from primary sensors are displayed in white unless cautionary or unsafe, while data from secondary sensors or data calculated from Dead reckoning are displayed in yellow.
Data from primary sensors are displayed in yellow while data from secondary sensors are display in white. Dead reckoning calculated data is displayed on red background.
The colors are there to make the display more appealing.
Correct Answer!
Q22.There is a continuous or dotted black line with a dot in the middle following the vessel, which does not show up in the “Object information” panel. What could it be?
A parallel index line.
A hidden chart object.
An edited chart line.
A radar target index line.
Correct Answer!
Q23.Where can you see whether the chart shows North up or other direction (course up, heading up, track up)?
In the lower left corner of the chart view.
In the icon bar in the upper right corner of the chart view.
In the sensor information panel.
|
|
|
Correct Answer!
Дата добавления: 2018-05-12; просмотров: 580; Мы поможем в написании вашей работы! |
Мы поможем в написании ваших работ!