Date, Time, and Breakpoint Ratio Settings(Table 2)
Universal Test Machine
Instruction Manual
Model: HD- B602
Power: 1 ЎУ Ј 220V, 50HZ
Preface
Thank you for choosing our products. We not only provide high quality products, but also reliable after-sales service.
In order to ensure operator safety and keep the machine well, please read the Operation Manual carefully before operating the instrument; pay more attention to the operating notes. This operating manual will illustrate the design principles, design criteria, structure, operation specification, calibration, maintenance, some failure case and solutions, electrical diagram, and so on. If this operating manual ever mentioned some expressions like Ў°test requirementЎ±, Ў°standardsЎ±, please note all of them would only be for your reference. Please review relevant standards or data by yourself if you disagree with this.
Special Statement:
Ўс The operating manual canЎЇt be treated as the proof to ask any illegal requirement to our company.
Ўс The interpretation of this manual owes to our company.
Haida International Equipment Co., Ltd
Phone: +86 769-89201068
Fax: +86-769-89280809
Service phone: +86 769-89201068
Website: www.haidatestequipment.com
Directory
Safety Attention ---------------------------------------------------------------------------------------------------4
ўс. Overview ------------------------------------------------------------------------------------------------------- 5
ўт. Design Standards----------------------------------------------------------------------------------------------5
ўу. Equipment Instruction --------------------------------------------------------------------------------------6-8
1. Structure ----------------------------------------------------------------------------------------------------------6
2. Control Panel-----------------------------------------------------------------------------------------------------7
3. Specification------------------------------------------------------------------------------------------------------7
4. Date, Time, Ratio and Breakpoint Settings----------------------------------------------------------------7-8
ўф. Equipment Installation --------------------------------------------------------------------------------------9
ўх. Operational Regulation -------------------------------------------------------------------------------------9-10
1. Specimen preparation -----------------------------------------------------------------------------------------9
|
|
|
2. Confirmation Before Test--------------------------------------------------------------------------------------9
3. Operation steps-------------------------------------------------------------------------------------------------10
ўц. Trouble Removal----------------------------------------------------------------------------------------------10
ўч. Maintenance Procedure ------------------------------------------------------------------------------------11
ўш. Quality Assurance --------------------------------------------------------------------------------------------11-12
ўщ. Note---------------------------------------------------------------------------------------------------------------12
Safety Attention
1. Safety labels:
These following labels are very important, please pay attention to them carefully when you using the tester.
Dangerous:
 This is safety label, the operator please pay attention it!
|
| Warning:
This shows that if you don't follow the project, may damage the apparatus.
|
Note:
|
| [Note].
This shows that the auxiliary statements of product in operation,
|
The sign below says note, warning
|
| Warning sign | This sign is on where need refer to operation specifications. |
| Dangerous voltage mark | The sign says for high risk. |
| Grounding mark | This is on the grounding terminals. |
ўс. Overview
1. Application:
The machine can be measured in a variety of materials and make tensile, tearing, peeling, adhesion...and resistance to physical properties.
2. Theory:
The machine is an electronic display peeling testing machine, using a motor drive screw to move the fixture, the test fixture with sample device is disposed between the upper and lower fixtures, and then is administered to a predetermined speed, the upward clamp peeling the specimen and the upper part of the fixture will feel the peeling strength; and the force is transferred into the voltage signal to the display, finally the LOAD CELL power sensor connecting display automatically shows the power value.
|
|
|
ўт. Design Standards
Test standards: ASTM D903ЎўGB/T16491ЎўGB/T1040ЎўGB/T8808ЎўGB13022ЎўGB/T 2790/2791/2792ЎўCNS-11888ЎўJIS K6854 and PSTC-7.
ўу . Equipment Instruction
Structure
 |
|
Description:
1. Sensor: the pressure plate to move up, the induction paper or cardboard pressure, and transmitted to the power display.
2. The upper fixture
3. The next fixture
4. The control panel (see details)
2. Control Panel
Specification(Table 1)
| Sensor | Load cell force sensor |
| Frame capacity | 200kg |
| Force reading | kg, N, LB |
| Display configuration | LCD display |
| Resolution | 1/10,000 |
| Load accuracy | ЎЬ1% |
| Max. stroke | 750mm including fixture |
| Test speed | 50-300mm/min (adjustable by rotary knob) |
| Power | 1ЎУ, AC220V, 50HZ |
| Weight | About 40kg |
( Table 1)
Date, Time, and Breakpoint Ratio Settings(Table 2)
| Steps | Operations | Display | Description |
| 1 | Turn on [POWER] Press [PRINT] key | ЎѕPS00000Ўї | Turn on [POWER], quickly press the [PRINT] button for more than 3 seconds (input password will see correction). |
| 2 | Press [PEAK] key Press [PRINT] key | ЎѕCAL 3Ўї | Input password, press [FUNCTION] key to shift the value, Press [PRINT] key to increase the number; Enter and press [PEAK] key to confirm, press [PRINT] key for three timesЈ then select CAL3, press [PEAK] key to confirm peak. |
| 3 | Press [FUNCTION] key Press [PRINT] key Press [PEAK] key | Ўѕd110722Ўї | Date setting If you want to modify, press [FUNCTION] key to shift the element, press [PRINT] key to increase the number; press [PEAK] key to confirm |
| 4 | Press [FUNCTION] key Press [PRINT] key Press [PEAK] key | Ўѕt101208Ўї | Time setting If you want to modify, press [FUNCTION] key to shift the element, press [PRINT] key to increase the number; press [PEAK] key to confirm |
| 5 | Press [FUNCTION] key | ЎѕPS00000Ўї | Password protection After starting, press and hold the [PRINT] key for more than 3 seconds |
| 6 | Press [FUNCTION] key Press [PRINT] key Press [PEAK] key | Ўѕb 850Ўї | Breakpoint ratio setting (eg: setting 850 for 85%) If you want to modify, press [FUNCTION] key to move the shift bit, press [PRINT] key to increase the number; press [PEAK] key to confirm. (NOTE: this is the factory setting. Please do not change arbitrarily) |
| 7 | Press [FUNCTION] key Press [PRINT] key Press [PEAK] key | ЎѕL001000Ўї | Small quantitative setting (NOTE: this is the factory settings) If you want to modify, press [FUNCTION] key to shift the value, press [PRINT] key to increase the number; press [PEAK] key to confirm, enter testing status. (NOTE: this is the factory setting) |
| 8 | Press [FUNCTION] key Press [PRINT] key Press [PEAK] key | ЎѕH090000Ўї | Large quantitative setting If you want to modify, press [FUNCTION] key to shift the value, press [PRINT] key to increase the number; press [PEAK] key to confirm, enter testing status. (NOTE: this is the factory setting) |
( Table 2 )
|
|
|
ўф. Equipment Installation
1. Power condition: Kindly connect correct power according to the nameplate on the machine.
| Danger:
Ўц The deviation of the in-put power is ЎА10%, and make sure the machine is well grounded to avoid electricity leakage.
|
2. Operating environment requirements: room temperature, 0-55ЎгЈГ, relative humidity, <80%, and far away from strong electromagnet.
3. It should be installed on horizontal position.
4. Please check if there are loose or failure of upper and lower limit before starting the machine, if happened, please amend and lock so as to avoid damage to the machine.
ўх. Operation Regulation
Specimen preparation:
1. Choose the specimen from the same lat.
|
|
|
Confirmation before test:
1). Make sure the machine is connected to the right power.
2). Do remember to wear the glove when touching the specimen.
3). Make sure the machine is horizontal.
Test steps:
1). Take the glove, check whether the machine power on, leak of electricity. After connect power, press [POWER] button, and power light is on. Now machine operating procedure will be open automatically.
2). Press the [UP] and [DOWN] button, you can rotate the [SPEED] control to enhance the speed of up and down. Confirm if protection device for up and down of the machine fixture is valid, and adjust the distance between the upper and lower fixture according to the test specimen.
3). Clamp and fix the test specimen with the upper and lower fixture.
4). Press the [CLEAR] button to ensure that the display shows 0.00, press the [PEAK] key, enter the test state.
5). Press the [UP] key for tensile test, the machine automatically stop running until the specimen is fractured or damaged.
6). The [DISPLAY] shows the maximum power of the test, record the value and press the [FUNCTION] key to save the maximum, and then press the [FUNCTION] key again to enter the print preparation; press the [PRINT] button to print the data;
7). Press the [DOWN] button, you can rotate the [SPEED] control to enhance the descending speed, so that the machine will back to the location before the test, press the [STOP] button, that is, this test is completed.
8). Test other groups of test specimen according to the above three to seven, calculate the average, that is, the maximum tensile force of the package value.
ўц . Trouble Removal
| Failure case | Possible Causes | Removal method |
| ЎсTurn on the [POWER] switch, the power switch is not lit. | ЎсThe power is not input. ЎсCheck the socket power supply. | ЎсChecked and repair power lines. ЎсCheck if the socket is plugged in. |
| ЎсPress the[UP] and [DOWN] key, the machine have no induction. | ЎсThe motor burns. ЎсThe key is damaged | ЎсReplace the motor ЎсReplace the button |
| ЎсSpeed can not be adjusted. | ЎсThe motor speed control board is damaged. ЎсThe potentiometer is damaged | ЎсReplace the speed control board ЎсReplace the potentiometer. |
| Note : ЎцIf the fault cannot be ruled out, please contact customer service with the company. |
|
ўч . Maintenance Procedure
1. Clearance: keep the machine clear and clean it with the cotton fabric before and after using each time.
2. Rust resistance: spray a layer of rust-resistant oil on the metal part of the machine every week. (and clean it after 2 hours )
3. Lube: fill lube (common one) at the rotating part of the machine (screw) every month regularly.
4. Check whether the screw is abrasive every half year, adjust and change it accordingly.
5. Check whether the gear oil of the reducer needs to be added or changed every year regularly.
ўш . Quality Assurance
A ) The quality assurance matters
The guarantee period with FOC within 1 year (not including expendable & transport and travel fees)
B) The main quality warranty maintenance certificate
If there is any dispute please refer to our guarantee letter, so:
ўЩ please keep the guarantee letter, if you lost it, please connect with us in a month.
ўЪ If the guarantee letter has been altered or it has no our stamp, it is useless.
C ) The following conditions need to be paid reasonably even in the assurance period:
ўЩ Natural reasons
ўЪ Operating mistakes
ўЫ Voltage is not fit for our operation instruction
ўЬ Repack it without our guides
ўЭ Damaged for borrowing to others
ўЮ Damaged for without authorized machine modification
ўЯ Damaged for without authorized calibration
ўа Without authorized transshipment mistake
ўб Serve for long distance area
D) Attentions
ўЩЎЎWhen the original installation in Dongguan, Shenzhen and the product moved to Dongguan, Shenzhen for using, regardless of whether during the effective guarantee period, transport and travel fees shall be paid by customer.
ўЪЎЎAny service outside Guangdong, China , transport and travel fees shall be paid by customer.
ўЫЎЎThe apparatus try not to be used in the following situations:
a. Vibration, rocking the occasion.
b. Direct sunlight.
c. Hot, dusty, damp places.
d. To ensure safe, AC supply of the machine should be well grounded.
e. Do not use strong solvents (such as: benzene, nitro oil) washing machine.
f. Do not inject water and debris into the machine; prevent damage to electrical comp1nts and electrical shock.
g. Instrument displays the disassembly and debugging can only be measured by the State Department approved the units and the company, other people not allowed to overhaul.
ўщ. Note
Any omissions in this instruction and any add instructions owe to the updated of the products are written here.
| This user is for your operating reference, the notes in it are very useful, please keep it. Our products are developing, this is user just fit for this kind of tester. Thank you!
 Мы поможем в написании ваших работ! |